U Tube Bundle Heat Exchanger
As per TEMA standard we can engineering and reverse engineering of U tube Heat exchanger and can duplicate your existing working U tube with custom build sizes and materials. Other Types of Tube Bundles are Fixed Tube Bundles, Removable Tube Bundles, Straight Tube, U Tube, Single Wall and Double Wall JC U Tube bundle Heat exchanger are useful for your higher-pressure and Higher Temperature applications requirements. We also supply U tube budle assemblies only. We assemble with proper care and needfull backup for transporting. Also testing repairing and cleaning of u tube bundle heat exchanger with expert team. You can use our U tubes for Hairpin type heat exchanger.
Double Pipe Heat Exchanger0 out of 5
The heat exchanger is completed of concentric inside also exterior pipe and the Heat exchangers are used to transfer the energy from one substance to another.
Types: Counter flow Parallel Flow Heat Exchanger Multi tube Double pipe exchangers Single tube Double pipe exchangers Countercurrent Double Pipe Heat Exchanger Double Pipe Hairpin Type Typical Double Pipe Heat Exchanger
Thermal Design Calculation: Q = UA ?Tlm After determination of the required heat transfer surface area, Other Mechanical Design are made, With reference to Process applications.
Applications: Tubeside with High pressure Pasteurization Low allowable pressure drop Digester heating Heat recovery High flow rate ratios High terminal temperature differences. Pre-heating Its dependable and once-through Effluent cooling. Especially in cases of process-temperature crosses
Advantages: High Efficiency International high quality Low Maintenance Cost Quick Heat Transfer
Air Cooled Heat Exchanger0 out of 5
Nearly all heat exchangers proceed as a heat sink, everywhere they are fast dissipating heat interested in the air that was built up at a new location. Air cooled heat exchangers are used by following reasons : They enlarge plant good organization, they make not necessitate an supplementary water supply .
Types Of Construction: Our Constructions types are Vertical and horizontal type
Types By Design: Forced Draft Air cooled Heat Exchanger Induced Draft Air cooled Heat Exchanger
Types By Flow: Counter-Current Flow Air cooled Heat Exchanger Co-Current Flow Air cooled Heat Exchanger Cross – Current Flow Air cooled Heat Exchanger
Types By Header: Plug header Cover plate header Welded bonnet type header Manifold header Pipe headers
Sources: Motors Drives Fans Structural vibration
Applications: Process Coolers / Condensers Cooling Tower Fans Cooling Water Coolers Air Cooler Fans Air Cooled Heat Exchanger for Oil & Gas Production Gas Coolers Gas Compressor Inter / After Coolers Air Cooler Fans Air Cooled Heat Exchanger for Power generation Cooling Tower Fans Steam Condensers Seal / Lube Oil Cooler Closed-Loop Cooling Water Coolers Geothermal Plant Condensers Air Cooler Fans Turbine lube oil coolers Turbine intercoolers
Stainless Steel Heat Exchanger0 out of 5
Stainless Steel Heat Exchangers are for the most part of useful in bad water environments caused by pollution or from the chemicals used to counter it. A heat exchanger systems are used to remove heat power from one medium to another without the two media individual varied.
Materials Of Construction: Stainless steel, Entrance Ports, Shell (Tough 316 stainless steel), Horizontal or Vertical Mounting, Clearances, Baffles
Features: Double Tubesheet, Carbon Steel Bolting, Insulated, Tubes, Mounting Feet. High efficiency and Low consumption Heat tranfer area : 5-500square meters It is prepared of imported stainless steel pipe.
Advantages: Easy maintenance and easy to install the SS heat exchanger All fluid get in touch with parts 316 Stainless Steel Materials Low power consumption
Flue Gas Air Preheater0 out of 5
Types: Tubular Type Regenerative Air Preheater Rotating Plate Regenerative Air Preheater Stationary Plate Regenerative Air Preheater
Applications: This type of air preheaters are a bit more straightforward in their design. They frequently seem to be large and boxy, and be able to take up a lot of space when compared with rotary air pre heaters.
Marine Heat Exchanger0 out of 5
The exchangers are the most common way to cool a boat’s engine, using the lake, river or ocean water in which the boat floats and also there are three methods employed for water-cooled marine petrol and diesel engines.
Parts: Mercruiser heat exchangers, Marine Water Pumps and other Marine Cooling Systems Parts
Applications: Gear Oil Coolers Fuel Coolers Hydraulic Oil Coolers Diesel Fuel Return Coolers Combination Coolers in Tandem Lube Oil Coolers
Advantages: The exchangers are very high efficient and best product. High Quality design with high heat transfer ability. The advantages and problem areas with different heat exchanger types and materials are discussed. Marine heat exchanger is its size, cost and ease of adapting existing cold water systems to hot. Researchers, over the years, have used a variety of heat exchanger types and materials. The application of heat exchangers to large scale marine aquaculture